Are you an aspiring bowler looking for ways to refine your game or a bowling enthusiast keen on discovering the nuances of the sport?
If so, one skill you should aim to have is learning how to bleed a bowling ball.
And that means taking time to select and bleed your new ball correctly in order for it to perform at its maximum potential on each lane it encounters.
In this blog post we will be discussing how to properly bleed your new bowling ball and why it’s such an important process in ensuring success on the lanes.
Whether you are an experienced bowler looking for some tips, or a beginner just getting started on
their journey–we’ve got helpful advice tailored specifically for everyone within this guide!
4 Best Ways to Bleed Your Bowling Ball — Take Your Pick!
Bleeding a bowling ball is an important process that all bowlers need to know.
It helps ensure that the quality of the ball is maintained and it also helps to maintain proper weight distribution when playing on a regular basis.
Bleeding your ball helps to reduce the amount of oil and dirt particles found inside the core, which can affect its performance.
This process is not as complicated as it may sound, but it does require some patience and attention to detail.
Here are some of the best ways you can bleed a bowling ball:
1). Bleeding with a Hot Water Bath:
You’d like to try a hot water bath method, you will need warm to hot tap water, a sink or bucket deep enough to submerge the entire ball, and a towel.
This method is best done outside as it can get messy!
Start by filling up your sink or bucket with warm-hot tap water, making sure it’s deep enough to completely submerge your ball.
How hot the water needs to be will depend on how reactive the coverstock is.
To test, put a few drops of water on the surface of the ball and if it bubbles or smokes then you know it’s too hot and needs to cool down slightly
Once at the right temperature, submerge the entire ball in the water for about 10-15 minutes.
This will allow enough time for the heat to penetrate deep into the coverstock and loosen up any embedded oils or microscopic dirt particles.
When finished, dry off your ball with a towel and you should be good to go.
You may notice that the surface of your ball is now a bit darker and more porous – this is totally normal and shows that the bleeding process has worked!
You can also use this method periodically to help remove excess oil buildup on the coverstock, which will help keep your ball’s original color and shine.
Just make sure not to leave the ball in the hot water bath for too long, as it can cause permanent damage to the coverstock.
Remember, bleeding a bowling ball is an important part of maintaining its performance over time and should be done at least once every 6 months!
If you follow these tips, you’ll always have a great performing ball that looks like new.
2). Using a Dishwasher:
- Begin by filling your dishwasher with a cup of white vinegar and placing the bowling ball in an open mesh bag to avoid scratches.
- Set the washer to its hottest water setting, and run it on a normal cycle.
- Let the machine finish its cycle, then take out the ball and inspect for any remaining debris or dirt.
- If necessary, repeat the process until all of the excess oil is removed from the ball.
- Finally, carefully dry the bowling ball with a cloth before using it again on the lanes.
- It is important to note that bleach or other abrasives should not be used when cleaning a bowling ball,
as they may damage the surface of the ball and affect its performance. - By following these steps to bleed a bowling ball, you can ensure that your equipment maintains its best playing condition for many games to come.
- Additionally, it is recommended to periodically clean and inspect your bowling balls in order to maintain their peak functionality.
3). Using a Car:
One way to bleed a bowling ball is to use a car. First, inflate the ball and place it in the trunk or backseat of your vehicle.
Make sure you secure it with rope and/or straps so that it does not move around during travel.
Next, drive for at least 30 minutes connecting highway and local roads. This will give the ball a good amount of time to vibrate and break in.
Finally, take the ball out of your car and you are ready to go.
4). Using a Heater:
The another method for bleeding a bowling ball is using a heater.
A heater is a device that helps to soften the surface of the bowling ball, making it easier to remove the logo or any other graphic from its surface.
To begin, place your bowling ball into the heating element, ensuring it is completely covered.
Leave it for 15 minutes and then carefully remove it with a pair of gloves – as it will be hot! Allow sufficient time
for the ball to cool down before attempting to scrape off any graphics from its surface.
Once you have completed this process, make sure to properly clean and polish your ball in order to keep it in optimal condition.
With these easy steps, you can now bleed a bowling ball successfully!
Conclusions:
Bleeding a bowling ball is not difficult, as long as you have the right tools.
It’s important to use the correct tools and procedures when bleeding a bowling ball since improper techniques may cause
damage or create unhealthy levels of oil inside your bowling ball.
Make sure you wear gloves and safety glasses while performing this task.
Additionally, be sure to hold the ball securely throughout the process so it doesn’t slip
or wobble in your hands while operating the drill bit.
Finally, never forget to clean off any excess oil from the surface of your new or freshly-bled bowling ball before taking it out for a spin at the lanes! With these tips in mind, you should be able to properly bleed your bowling ball with ease!